For this purpose of this walkthrough it is assumed that the steps to establish a working Point to Site VPN have been completed. If you have also established a working Site to Site VPN following this walkthrough it will stop the it working correctly. The walkthrough assumes that the virtual network appliance is using the Barracuda NextGen Firewall F-Series virtual network appliance.

  1. Create an subnet in your VNET with the following settings Name:frontend and Address Range (CIDR Block) : 10.160.3.0/24
  2. Using the Azure MarketPlace create an instance of the virtual network appliance. This is a “Barracuda NextGen Firewall F-Series (PAYG)”. You will be charged for it use so you’ll want to ensure that these costs are factored into any planning. You are asked a number of things when setting this up. The important things for this walkthrough are that it is in its own resource group and it is connected to the frontend subnet you just created. Make a note of the password you use – it will be needed later.

fw1
Notice that you will be charge for the Barracuda License outside of any Azure Credit you might have.

fw2

  1. The Virtual Network Appliance needs to act as a network gateway, capturing traffic that is not address directly to it and forwarding it on to its destination. In order to do this IP forwarding needs to be enabled on the Network Interface for the Virtual Network Appliance.

fw3

  1. Create a Route Table that will route all Internet bound traffic to the virtual network appliance. In this example, I’m controlling the public IP so I’ll restrict the rule to just this IP. This means that I’ll still be able to connect to my VM over the Internet without issues. In production scenarios, you’ll have to think a bit harder about how the routes should be set up. Ensure that the route table is created in the network resource group.
  2. In the newly created route table create a route that routes traffic that needs to go through the virtual network appliance. Ensure that you have the following settings, Next Hop Type: Virtual Appliance & Next Hop Address: . If you are using a single IP remember you’ll still need to use CIDR notation. That means appending /32 to the end of the address.

fw4

  1. Assign the route table to the GatewaySubnet and the Backend Subnets.
  2. Through the service plan for the App Service, navigate to the networking option and then click to Manage the VNET Integration. Under the VNET Integration you need to add an entry to the IP ADDRESSES ROUTED TO VNET section. For this walkthrough you can set the start and end address to that of the external endpoint you are connecting to. For production scenarios use an appropriate address range. Take into consideration other services that the application might use, such as SQL Azure and Redis cache. By default all these connections are over the Internet so if you are not careful, you can route traffic for these connection into your VNET.

fw5

Configuring the Firewall

When the Firewall is setup up it will be secure by default and as such it will not know what to do with traffic destine to your external endpoint. Therefore, it will need to be configured to allow this traffic to flow. The Barracuda Firewall runs on Linux so connecting to it is a bit different to connected to a Windows machine. Luckily Barracuda provide a Windows Desktop application that takes away much of the pain.

  1. Download the Barracuda NextGen Admin application from the Barracuda website. You’ll need to create an account to achieve this. https://login.barracudanetworks.com/account/
  2. Once logged in go to Support -> Download and then select Barracuda NextGen Firewall project. On the resulting page select NextGen Admin as the Type and select the most recent version of the Barracuda NextGen Admin tool

fw6

  1. Run the NGAdmin tool and enter the public ip of the Virtual Network Appliance assigned to it by Azure. Then use Root of the username and enter the password you used when creating the appliance.

fw8

  1. The operation of the firewall software is broadly split into two roles. One for monitoring the system and the other for configuring it. If you click on the Firewall Tab at the top you’ll enter a screen that allows you to monitor firewall operations. From this screen you can do things such as seeing live and historic traffic cross the firewall and see what is allowed and what it blocked. On clicking the Forwarding Rules you can see how those access rules are defined. Luckily there is already a rule called LAN-2-INTERNET that manages access from the internal LAN (The Azure VNET in our case) and the Internet. The main problem is the software as it stands does not know the address ranges that represent our network. To change that we’ll have to use the configuration part of the software.

fw7

  1. Click on the configuration tab. The options to change the forwarding rules are very well hidden. Navigate to Box / Virtual Servers / S1 () [xxx] / Assigned Services / NGFW (Firewall) / Forwarding Rules

fw9

  1. On the resulting screen, you need to change the definition of the LAN-2-INTERNET rule. In the Source field you’ll find “ref: Trusted LAN”. If you drill into that by double clicking you’ll find that this in turn is defined as “Ref:Trusted LAN Networks” and “Ref:Trusted Next Hop Networks”. Again, by drilling in you’ll find that only “Ref: Trusted LAN Networks” is defined as 127.0.0.0/24. This is not sufficient for our needs.

fw10

  1. This rule needs to allow traffic that originates both from our VNET and from the VPN clients used to establish the Point to Site VPN from the App Services to the VNET. In production scenarios it would make sense to create groups to represent these address ranges and add them to the list of references defined by “Ref:Trusted LAN”. However, to keep things simple the rule can be updated directly.
  2. Add the address ranges 10.10.1.0/24 (Point to Site VPN Clients) and 10.160.0.0/16 (VNET) as sources. Note that the software locks down the UI to avoid mistakes creeping in. Therefore, you must Unlock the UI (by clicking LOCK bizarrely).

fw11

  1. Activate the changes by clicking “Send Changes” then clicking on “Activation Pending” and finally the “Activate” button
  2. This should be enough to browse from a VM on the backend subnet to the external resource. You can see traffic flowing from the Firewall tab under History. If the firewall is blocking traffic you’ll also see it here.

fw12

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s